Dymonic® FC is a high-performance, fast-curing, single-component, low-modulus, hybrid sealant, formulated with proprietary silane end-capped polymer technology.
|Dymonic FC Data Sheet|
|Dymonic FC Color Chart|
|Dymonic FC Almond SDS|
|Dymonic FC Almond SDS (CAN)|
|Dymonic FC Aluminum Stone SDS|
|Dymonic FC Aluminum Stone SDS (CAN)|
|Dymonic FC Anodized Aluminum SDS|
|Dymonic FC Anodized Aluminum SDS (CAN)|
|Dymonic FC Beige SDS|
|Dymonic FC Beige SDS (CAN)|
|Dymonic FC Black SDS|
|Dymonic FC Black SDS (CAN)|
|Dymonic FC Bronze SDS|
|Dymonic FC Bronze SDS (CAN)|
|Dymonic FCC Buff SDS|
|Dymonic FCC Buff SDS (CAN)|
|Dymonic FC Dark Bronze SDS|
|Dymonic FC Dark Bronze SDS (CAN)|
|Dymonic FC Gray SDS|
|Dymonic FC Gray SDS (CAN)|
|Dymonic FC Hartford Green SDS|
|Dymonic FC Hartford Green SDS (CAN)|
|Dymonic FC Ivory SDS|
|Dymonic FC Ivory SDS (CAN)|
|Dymonic FC Light Bronze SDS|
|Dymonic FC Light Bronze SDS (CAN)|
|Dymonic FC Limestone SDS|
|Dymonic FC Limestone SDS (CAN)|
|Dymonic FC Natural Clay SDS|
|Dymonic FC Natural Clay SDS (FR)|
|Dymonic FC Off-White SDS|
|Dymonic FC Off-White SDS (CAN)|
|Dymonic FC Precast White SDS|
|Dymonic FC Precast White SDS (CAN)|
|Dymonic FC Redwood Tan SDS|
|Dymonic FC Redwood Tan SDS (CAN)|
|Dymonic FC Stone SDS|
|Dymonic FC Stone SDS (CAN)|
|Dymonic FC White SDS|
|Dymonic FC White SDS (CAN)|
The service temperature range for polyurethane sealants is -40°F to 185°F (-40°C to 85°C).
Physically remove excess sealant by wiping, scraping or cutting. Residual traces of sealant can be removed by wiping the surface with a cloth or abrasive pad saturated with a solvent such as mineral spirits or xylene. Test a hidden area of the surface to be cleaned to ensure no adverse effects due to solvent interaction. Where abrasive pads are used, care should be exercised in order to ensure the surface appearance is not adversely effected.
The surface temperature of the substrate should be less than 150°F (66°C) at the time the sealant is applied.
The surface temperature of the substrate should be 40°F (4°C) and rising or above at the time the sealant is applied. It is also recommended that the sealant be stored at room temperature prior to application.
Polyurethane sealants are paintable once they are fully cured. Adhesion of the paint to the sealant should be evaluated through a site mockup to determine appropriateness of use. Additionally, for applications involving dynamically moving joints, it should be expected that the paint film will tear exposing the sealant below. For this reason, it is recommended that the sealant and the paint be of similar colors.
Curing of polyurethane sealants occurs at approximately 1/16” (1.66mm) depth per day at 75°F (24°C) and 50% RH. The cure time will increase as the temperature and/or humidity decreases. A good rule of thumb is an additional 24 hours of cure for every 10°F (-12°C) decrease in temperature.
The shelf life for Tremco polyurethanes is 6 to 24 months depending on type of sealant and/or packaging. Please contact Technical Service for specific shelf life of a product at 866-209-2404.